Adel Taha Abbas (Adel T Abbas)

Publication Activity (10 Years)

Years Active: 2018-2022
Publications (10 Years): 9

Top Topics

Rheumatoid Arthritis

Systematic Review

Top Venues

Materials (Basel, Switzerland)

This page only lists publications with an associated author ORCID identifier.

Publications

Adel Taha Abbas, Abdulhamid A Al-Abduljabbar, Ibrahim Abdullah Alnaser, Mohamed F Aly, Islam H Abdelgaliel, Ahmed Elkaseer
A Closer Look at Precision Hard Turning of AISI4340: Multi-Objective Optimization for Simultaneous Low Surface Roughness and High Productivity. Materials (Basel, Switzerland) 15 (6) (2022)
Adel Taha Abbas, Saqib Anwar, Elshaimaa Abdelnasser, Monis Luqman, Jaber E Abu Qudeiri, Ahmed Elkaseer
Effect of Different Cooling Strategies on Surface Quality and Power Consumption in Finishing End Milling of Stainless Steel 316. Materials (Basel, Switzerland) 14 (4) (2021)
Adel Taha Abbas, Essam A Al Bahkali, Saeed M Alqahtani, Elshaimaa Abdelnasser, Noha Naeim, Ahmed Elkaseer
Fundamental Investigation into Tool Wear and Surface Quality in High-Speed Machining of Ti6Al4V Alloy. Materials (Basel, Switzerland) 14 (23) (2021)
Adel Taha Abbas, Neeraj Sharma, Saqib Anwar, Monis Luqman, Italo Tomaz, Hussien Hegab
Multi-Response Optimization in High-Speed Machining of Ti-6Al-4V Using TOPSIS-Fuzzy Integrated Approach. Materials (Basel, Switzerland) 13 (5) (2020)
Adel Taha Abbas, Magdy M El Rayes, Monis Luqman, Noha Naeim, Hussien Hegab, Ahmed Elkaseer
On the Assessment of Surface Quality and Productivity Aspects in Precision Hard Turning of AISI 4340 Steel Alloy: Relative Performance of Wiper vs. Conventional Inserts. Materials (Basel, Switzerland) 13 (9) (2020)
Adel Taha Abbas, Saqib Anwar, Hussien Hegab, Faycal Benyahia, Hazem Ali, Ahmed Elkaseer
Comparative Evaluation of Surface Quality, Tool Wear, and Specific Cutting Energy for Wiper and Conventional Carbide Inserts in Hard Turning of AISI 4340 Alloy Steel. Materials (Basel, Switzerland) 13 (22) (2020)
Adel Taha Abbas, Faycal Benyahia, Magdy M El Rayes, Catalin Iulian Pruncu, Mohamed A Taha, Hussien Hegab
Towards Optimization of Machining Performance and Sustainability Aspects when Turning AISI 1045 Steel under Different Cooling and Lubrication Strategies. Materials (Basel, Switzerland) 12 (18) (2019)
Adel Taha Abbas, Neeraj Sharma, Saqib Anwar, Faraz H Hashmi, Muhammad Jamil, Hussien Hegab
Towards Optimization of Surface Roughness and Productivity Aspects during High-Speed Machining of Ti-6Al-4V. Materials (Basel, Switzerland) 12 (22) (2019)
Adel Taha Abbas, Danil Yurievich Pimenov, Ivan Nikolaevich Erdakov, Mohamed Adel Taha, Mahmoud Sayed Soliman, Magdy Mostafa El Rayes
ANN Surface Roughness Optimization of AZ61 Magnesium Alloy Finish Turning: Minimum Machining Times at Prime Machining Costs. Materials (Basel, Switzerland) 11 (5) (2018)